View and Download Isuzu Trooper 1999 workshop manual online. Trooper 1999. Trooper 1999 Automobile pdf manual download. Also for: Trooper ux 1999.
![Workshop Workshop](/uploads/1/2/5/3/125384373/137339870.png)
.HOME SECTION TABLE OF CONTENTS Click GENERAL INFORMATION General Information Maintenance and Lubrication HEATING, VENTILATION AND AIR CONDITIONING WORKSHOP MANUAL HVAC Systems STEERING Power Assisted System TROOPER SUSPENSION Front Suspension (UX) Rear Suspension Wheel and Tire System DRIVELINE/AXLE Differential (Front) Differential (Rear) Driveline Control System (SHIFT ON THE FLY) Driveline Control System (TOD).The SRS system equipped vehicle can be identified efficient and reliable performance of service repairs. Use genuine Isuzu parts. “AIR BAG” warning light on the instrument panel. Used cotter pins, plastic clips, gaskets, O–rings, oil 2.0A–2 GENERAL INFORMATION Illustration Arrows Arrows are designed for specific purposes to aid your understanding of technical illustrations.
Arrow Type Application Arrow Type Application f Ambient/Clean air flow Front of vehicle f Cool air flow f Gas other than ambient air Up Side f Hot air flow f Ambient air mixed.GENERAL INFORMATION 0A–3 Identification Vehicle Identification Number (VIN) This is the legal identification of the vehicle. It is located on the left bottom of the windshield. It can be easily seen through the windshield from outside the vehicle. 710RX001 F00RX007.0A–4 GENERAL INFORMATION Engine Serial Number Automatic: Stamped on the identification plate, located on the left side of the transmission above the mode The gasoline engine serial number is stamped on the left switch. Rear lower area of the cylinder block above the starter.
240RW012 F06RW001 Transmission Serial Number.GENERAL INFORMATION 0A–5 Theft Prevention Standard The 11 major components listed below will be marked with 17 digit V.I.N. At the stage of production. In addition its service parts will be marked with manufacturer’s trade mark, “R” mark and “DOT” mark. INDICATION Reference COMPONENT.0A–6 GENERAL INFORMATION Anti Theft Stamping/Label/Plate Location The stamping, label and plate locations are indicated by arrows in the illustration below. VIN plate locations for production. Stamping locations for service parts. Engine 901RW195 Manual Transmission (AR–5) 901RX021.GENERAL INFORMATION 0A–7 Automatic Transmission (THM) 901RW197 Body 901RW113 Legend (6) Fender (3) Engine Hood (7) Rear Quarfer Panel (4) Front Door (8) Front Bumper (5) Rear Door.0A–8 GENERAL INFORMATION Body 901RW114 Legend (10) Back Door Right Side (9) Back Door Left Side (11) Rear Bumper.GENERAL INFORMATION 0A–9 Body Label Instructions Do not peel off the masking tape until completion of paint work when replacing these parts, as the tape is affixed on the label attached to service parts for body of the anti–theft component.
NOTE: Be sure to pull off the masking tape after paint work has been completed.0A–10 GENERAL INFORMATION Lifting Instructions CAUTION: f If a lifting device other than the original jack is used, it is most important that the device be applied only to the correct lifting points. Raising the vehicle from any other point may result in serious damage.
F When jacking or lifting a vehicle at the frame side rail or other prescribed lift points, be certain that lift pads do not contact the catalytic converter, brake pipes or.GENERAL INFORMATION 0A–11 Lifting Point; Front Lifting Point; Rear f When using a floor jack, lift on the center of the skid f Position the floor jack at the center of the rear axle plate. Case when lifting the vehicle. 545RS001 420RS002 Supportable Point.0A–12 GENERAL INFORMATION Supportable Point; Rear f Position the chassis stands at the bottom of the rear axle case. 420RS001.GENERAL INFORMATION 0A–13 Standard Bolts Torque Specifications The torque values given in the following table should be applied where a particular torque is not specified.